|
|
|
|
|
|
|
|
|
|
|
|
|
|
Adjust from low air to a full volume flow. Recommended air pressure to 150 psi maximum. Knurled nozzle makes handling easy. Complete with handy pocket clip. Fits all industrial/Milton design 1/4 in coupler bodies.
|
|
Conforms to all Federal requirements related to OSHA, including noise level regulations. Tamperproof pressure reducers built into this gun limit nozzle pressure to 30 psi or less when used with listed inlet pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy-duty die-cast, epoxy finish body. Complete with hang-up hook and 1/4 in female NPT inlet.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Safety blow gun.
|
Converts any standard ball foot tire chucks to a safety blowgun. Vented nozzle and built-in pressure reduces limit nozzle pressure to a maximum of 30 psi, with up to 150 psi inlet pressure. Conforms to #1001 OSHA regulation. Epoxy finish.
|
Vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy-duty die-cast body. Hang up hook and 1/4 in NPT female inlet included. Meets OSHA regulation 1001 for 30 psi "dead head" pressure. Inlet pressure rating of 150 psi.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ideal for cleaning damaging dirt and grime buildups from large machinery, engines and heavy equipment.
|
Increased performance and yet still meets OSHA regulation 100-1 for 30 psi "dead head" pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy-duty die-cast body. Complete with hang-up hook and 1/4 in NPT female inlet. Inlet pressure of 150 psi.
|
Allows full line pressure to be used. Oil-resistant, soft replaceable rubber tip. Will not mar delicate surfaces. Gives a leakproof seal against oil passages, fuel lines and more. When air pressure is needed for cleaning.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Interchangeable nozzles for cleaning and inflating. Complies with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 psi. Includes standard nozzle, tapered inflator nozzle and ball inflator nozzle.
|
Meets OSHA regulation 100-1 for 30 psi "dead head" pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy-duty die-cast body with hang-up hook, 1/4 in NPT female inlet and 4 in extension.
|
Comfortable thumb lever valve control with handy hanger in lever and hanger hook. Compact one-piece nozzle. Allows full line pressure to be used. Includes 1/4 in female NPT inlet. To comply with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 psi.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Combination of a blowgun and the siphon spray nozzle. Barbed siphon inlet fits 1/4 in ID hose or tubing. Use for spray, cleaning engines, applying protective coating and more. Allows full line pressure to be used. Includes 1/4 in female NPT inlet. To comply with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 psi.
|
Tru-Flate Hi Flo? blowguns combine ergonomics with power for an enhanced experience.
|
The ProSource tire inflator has a die-cast body and dial type gauge with rubber protector and it has a fitted single clip-on connector. There is an air pressure of 0 to 220 psi and an air inlet of 1/4 in NPT.
|
|
|
Estimates